Gday Josh,

We'd recommend the 2 burner hot plate to go with the 2 burner low-pressure stove.
Hope that helps!

G'day Allerina,

No, there's not enough room inside the stove itself, so the hotplate will need to be packed separately.

G'day Gianna,

We've actually tried this one out before from a question asked on the stove page, and its a great fit!

G'day Barry,

Yes, there is, just head down to the "you might also like" section below the Q&As. You'll find the Campfire Pioneer 3 Burner Hotplate Bag.

G'day Anthony,

The 3 Burner Gas Cooker Plate is a little too wide to safely use with the Zempire 2 Burner Deluxe Camp Stove. We'd suggest grabbing the 2 Burner Gas Cooker Plate Instead. 

G'day John,

The Coleman 3 Burner Eventemp Stove comes with a hotplate, but if you're wanting to replace a missing or damaged plate then the Campfire 3 Burner Gas Cooker Plate will fit the Eventemp Stove, but is a little narrower than the plate originally supplied with the stove.

G'day Nathan,

Yes the Campfire 3 Burner Gas Cooker Plate is compatible with the HyperFlame FyreKnight stove.

G'day Fernando,

Yes, the Campfire 3 Burner Gas Cooker Plate will suit the Companion 2 Burner High Output Stove.

G'day Dan,

If you lay the handles outwards on the Campfire 3 Burner Gas Cooker plate, then it lays flat but you can't lay them flat over the plate itself. You can remove them if you want to though and then slide them back on when you're using the plate again. 

G'day Kylie,

We don't sell Wild Country stoves, so I can't check this one to be 100% certain for you but I do know that the Campfire 3 Burner Gas Cooker Plates are designed to fit most 3 burner stoves, so you would most likely be alright with this one. 

G'day Sang,

I've just had a play with one of the Campfire 3 Burner Gas Cooker Plates myself and I tend to agree with your thought around the hands not being sturdy enough to hold the hotplate off of the fire. You'd either need to place the hotplate directly on the fire or look at an option like the Flat Plate Campfire Cooker.

G'day Alan,

I've just popped down to the shop floor to give one of the Campfire 3 Burner Gas Cooker Plates a try on the Primus 2 Burner High Output Stove. Good news, it felts well! It does touch the wind guards on the side, but it doesn't push them out at all. 

G'day Mark,

That's a great question mate, which we've not been asked before. We're not actually sure the answer, as it seems what your saying would theoretically be correct. We'll have to check this one out with the guys at Companion and get back to you with an answer.

G'day Mark,

We haven't heard from Companion, but I've undertaken some research for you. The hotplate will require some maintenance as you use it which includes re-seasoning as required. This will be for both the cooking and burner sides.

The hotplate actually comes with a very helpful booklet to step you through each process and what to look for when needing to re-season or handling rust if it starts to develop etc. I've just had a read through the booklet and it's quite informative.

G'day Glen,

We, unfortunately, don't have any Coleman 2 Burner Dual Fuel Powerhouse Stoves in stock so I can't physically check. However, from looking at dimension specifications, it appears to me that the 3 Burner Gas Cooker Plate would be the way to go.

G'day Judy,

Yes the Campfire 3 Burner Gas Cooker Plate will fit with the Fyrecadet no worries. 

G'day Richard,

The 52cm length of this plate is for the cooking plate only. The entire length of the plate including loops and handles is about 57cm in total.

G'day Cherise, 

The 3 Burner Gas Cooker Plate isn't going to be a good fit for the Gasmate 2 Burner Stove with Griller as it's a bit too big. A better fit would be the Primus 2 Burner Gas Cooker Plate - this one should be the perfect size! 

G'day David,

I've just had a look at the box and I've found that the Campfire 3 Burner Gas Cooker Plate is pre-seasoned - so you won't have to do any seasoning before use.